Can-Am 2017-2021 Maverick X3 850W Magneto

What's in the Box

Included parts

- Always wear EYE PROTECTION AND APPROPRIATE GLOVES when using power

- Unless otherwise specified, engine must be OFF when performing any

vehicle.

- Always be aware of parts that can move, such as wheels, transmissio

NOTE: USE TIGHTENING TORQUES IN THE FOLLOWING TABLE IF NOT OTHERWISE

SPECIFIED.

GRADE

5.8 8.8 10.9

1.8 ± 0.2 N•m 2.8 ± 0.2 N•m 3.8 ± 0.2 N•

(16 ± 2 lbf•in) (25 ± 2 lbf•in) (34 ± 2 lbf•

3.3 ± 0.2 N•m 5 ± 0.5 N•m 7.8 ± 0.7 N•

(29 ± 2 lbf•in) (44 ± 4 lbf•in) (69 ± 6 lbf•

7.5 ± 1 N•m 10 ± 2 N•m 12.8 ± 2.2 N

(66 ± 9 lbf•in) (89 ± 18 lbf•in) (113 ± 19 lbf

15.3 ± 1.7 N•m 24.5 ± 3.5 N•m 31.5 ± 3.5 N•

(135 ± 15 lbf•in) (18 ± 3 lbf•ft) (23 ± 3 lbf•

29 ± 3 N•m 48 ± 6 N•m 61 ± 9 N•m

M10

(21 ± 2 lbf•ft) (35 ± 4 lbf•ft) (45 ± 7 lbf

52 ± 6 N•m 85 ± 10 N•m 105 ± 15 N•m

M12

(38 ± 4 lbf•ft) (63 ± 7 lbf•ft) (77 ± 11 lbf

85 ± 10 N•m 135 ± 15 N•m 170 ± 20 N•m

M14

(63 ± 7 lbf•ft) (100 ± 11 lbf•ft) (125 ± 15 lbf•

126 ± 14 N•m 205 ± 25 N•m 255 ± 30 N•m

M16

(93 ± 10 lbf•ft) (151 ± 18 lbf•ft) (188 ± 22 lbf•

170 ± 20 N•m 273 ± 32 N•m 330 ± 25 N•

M18

(125 ± 15 lbf•ft) (201 ± 24 lbf•ft) (243 ± 18 lb

The illustrations in this document show typical construction of the d

not reproduce the full detail or exact shape of the parts; however, t

the same or similar function.

Installation time is approximately2.5 hours.

parts to be installed

ITEM DESCRIPTION

P1 850W Rotor ass'y

P2 Stator plate

P3 Voltage Regulator

P4 Cable Support

P5 Voltage Regulator Support

P6 Gasket (magneto)

P7 Gasket (water pump)

P8 Gasket (oil cooler)

P9 M6 X 30 Socket Head Screw 20506

P10 M6 Elastic Nut 233261

P11 M6 Flat Washer 234062

P12 7603 DIN Washer 504082

P13 173 mm Locking Tie 293750

P14 371 mm Locking Tie 293750

Required tools

tools.

operation on the

n components, etc.

12.9

m 4.5 ± 0.5 N•m

in) (40 ± 4 lbf•in)

m 9 ± 1 N•m

in) (80 ± 9 lbf•in)

•m 16 ± 2 N•m

•in) (142 ± 18 lbf•in)

m 40 ± 5 N•m

ft) (30 ± 4 lbf•ft)

73 ± 7 N•m

•ft) (54 ± 5 lbf•ft)

128 ± 17 N•m

•ft) (94 ± 13 lbf•ft)

200 ± 25 N•m

ft) (148 ± 18 lbf•ft)

305 ± 35 N•m

ft) (225 ± 26 lbf•ft)

m 413 ± 47 N•m

f•ft) (305 ± 35 lbf•ft)

ifferent assemblies and may

hey represent parts that have

Part number QTY

420686194 1

420686363 1

710006824 1

710007104 1

710006987 1

420431640 1

420431682 1

420431870 1

3044 3

414 4

670 2

900 1

009 5

018 20

Installation

5 ± 0.6 N•m (44 ± 5 lbf•in) Oil cooler retaining screw.

9 ± 1 N•m (80 ± 9 lbf•in) Reinstall the water pump housing with a new gasket [P7]. Tighten retaining screws to specification as per the following procedure.

Shop this kit → Create a Support Ticket

Note: This product is exempt from the emission standards and related requirements of 40 C.F.R. § 1051 as provided by 40 C.F.R. § 1051.620, and California law [e.g., vehicle code§§ 27156 and 38391]. This product is sold only for use in connection with EPA certified, purpose-built, nonroad vehicles used solely for closed course, nonroad competition/racing and not used for any recreational purpose or on public highways or right of ways maintained by and open to the public. This product is sold only in connection with machines that do not fall under state and/or federal noise or emission standards/regulations. Purchasers who/that purchase this product represent and warrant that the product is purchased only in connection with EPA -certified, emission-regulations-exempt and noise- regulations-exempt competition/racing vehicles as interpreted under applicable state and/or federal law. Questions: Call Evolution Powersports at (715) 247-3862.

Can-Am 2017-2021 Maverick X3 850W Magneto — Install Guide

Can-Am · Maverick X3

What's in the Box

Installation